Looking for:
SILENT KNIGHT INSTALLATION, PROGRAMMING, AND OPERATION MANUAL Pdf Download | ManualsLib. |
.
- Troubleshooting
Place the four plastic stand- offs into the bracket and snap onto the PC board. Page Model Direct Connect Module The maximum coil and wire resistance combined must not exceed 30 ohms. To install the for city box connection: 1. Locate the knockout on the right side of the cabinet to connect the using a short piece of conduit must not exceed 20 feet in length. Page Nfpa 72 Polarity Reversal To install the for polarity reversal, follow the steps below: 1.
Refer to the installation sheet shipped with the 95M for complete information. Note: The is not available from Silent Knight. It also provides trouble and alarm information and can be used for programming.
When the annunciator powers up, it will dis- play its ID code and current status of the panel. A temporary can be connected for programming and troubleshooting. See Section 4. Page Model Signal Power Expander The Model is a notification and auxiliary power expander that provides up to 6. Figure shows you how to connect the Model to the Model panel. Page Model Zone Converter 4.
Figure and Figure show how to make conversions. Page Supervised Notification Appliance Outputs Figure shows how to connect the notification circuits to the Contact Silent Knight if you have any questions about compatible notification circuits. Page Auxiliary Relays loss of AC, low battery, failed to communicate, phone line troubles, and notification circuit troubles.
Refer to the programming manual for more information. Figure shows the relay contact connections using a doorstrike application as an example. Page Operation Section 5 Operation To operate the you can use either the built-in touchpad or the Model Remote Annunciator. Note that if no keys are pressed for 15 minutes while in program mode, the system will time out and resume normal operation.
For complete information and for display messages, see Section 9. Table Built-in Touchpad Display Codes Page Led Indicators Operation 5. The chart below explains the meaning of these LEDs. In walk test mode, the built-in self test on the ESL series smoke detectors may be unreliable. If the built-in self test is required, it should be done in the normal operating mode with the zone speed set to 3 seconds or higher.
Please read Section 7 thoroughly, especially if you have never programmed the before. The quick reference chart can be used for keeping track of how options have been pro- grammed for an installation. You must be in Step Programming Mode also known as mode 27 to program the panel. See the following sections for details.
Using Step Programming The digits appear on the right side of the display and scroll to the left as you continue to enter data.
The way you move through Mode 27 may also vary from how it is described here. Enable the printer if your installation includes a printer in- terface.
The is not UL listed for use with the Enables 24V power. Do NOT disable. These digits are reserved by the manufacturer for future use.
Page Step 3. More System Options Display Description Step 3 allows you to select seven system options shown below. To select an option, press its number. If you select this option, bells will pulse in the pattern shown below for customizing patterns, refer to Steps 27 and 28 : 3.
Page Step 5. Miscellaneous Options Display Description Step 5 is for programming several system options, including bell supervision. Select this option if you want walk tests reported to the central station.
Page 60 Note: This very fast response time can increase the possibility of false alarms, since transients and other interference can set off alarm conditions in such a short time span. Silent Knight recommends that you do not use this response time unless you have to because, for example, the installation you are protecting requires this quick a response time even if false alarms could result.
Zones sec. Zone 8: sec. Page Step 7. Must be selected for all zones. Do NOT change the factory programming for this step. Page Step 8. If you want the to try again to send a report 15 minutes after all previous attempts have failed, select 0.
Choose if using a second phone line with the system. Page Step Select a number from 5 to For a local- only system, select "0" for this step and for Step Step Select for phone numbers Computer Phone Number Step Central Station Phone Numbers Display Description The can report to four different central station telephone numbers.
Two are required. Enter the numbers in Steps See Step 15 if you need to know how to select digits and special characters for phone numbers. This number is how many times the dialer will attempt to report to this account number before switching to the next number. Duration of Delays Display Description Bell Shutdown Time Divide by 10 and enter the number indicating the time that you want audio alarms to be active.
Example: Suppose you want audio alarms to be active for seconds or 15 minutes. Test Time The can have up user codes, but the annunciator can program only 10 codes codes If you need more than 10 codes, use the downloading software. Relays and bells are programmed for the type of condition that causes them to activate, not by zone. An excep- tion is relays and bells that activate for alarms, which can be programmed by zone.
Press to select Bell 1 b. Press to select Bell 2 c. Press to select Bell 3 d. Alarm relays always remain active until reset. You can use this step to program a trouble relay to remain active after the panel is silenced. Digit 1 programs the audible signals for the zone. Digit 2 programs the zone type. Move through the steps to make sure that all zones in your installation have been programmed the way you want them to be. Zone Location Descriptions For Steps You can choose one- or two-word descriptions for each zone from the word list library shown below.
Note: You cannot customize the library using the annunciator. If you want to use words other than those contained in the library, you must use the downloading software.
Page Steps 27 And Temporal Patterns Display Description Steps 27 and 28 are used together to control the temporal pulsing pattern of the bell outputs. You can use these steps to create any temporal pattern you want, including the pattern required by NFPA Select a digit for each half-second ON; de-select a digit display shows a dash for each half-second OFF. Each sub-step controls up to four seconds.
Zones interchangeable using the Model Zone Converter. Event Memory. Fuseless design reduces service 24 VDC power supply. Compatible with 2- and 4-wire detectors as well as water and sounding devices. ANSI cadence pattern output. Four programmable Style Y signal circuits, including pulse and temporal. Programmable smoke verification, delay, and cross-zoning minimize false alarms. Four general purpose relays Form 24 V at 2.
Built-in approved digital with UL required reporting. Accu-Zone diagnostics facilitate and remote troubleshooting. Walk Test. Its fourteen function keys perform the same operations as main system annunciator, including resetting, and the displaying alarms, troubles and alarm memory.
No comments:
Post a Comment